Its not installed.
Installed it.
wadesmart@wadesmart:~$ smartctl --all /dev/sdb
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Smartctl open device: /dev/sdb failed: Permission denied
wadesmart@wadesmart:~$ sudo smartctl --all /dev/sdb
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9 family
Device Model: Maxtor 6Y200P0
Serial Number: Y65QDNEE
Firmware Version: YAR41BW0
User Capacity: 203,928,109,056 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sat Jun 12 17:42:15 2010 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 243) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 91) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 189 183 063 Pre-fail
Always - 24633
4 Start_Stop_Count 0x0032 253 253 000 Old_age
Always - 293
5 Reallocated_Sector_Ct 0x0033 115 114 063 Pre-fail
Always - 1404
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 253 243 187 Pre-fail
Always - 61145
9 Power_On_Minutes 0x0032 183 183 000 Old_age
Always - 534h+55m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age
Always - 382
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 42
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 2646
196 Reallocated_Event_Count 0x0008 001 001 000 Old_age
Offline - 1321
197 Current_Pending_Sector 0x0008 131 131 000 Old_age
Offline - 1237
198 Offline_Uncorrectable 0x0008 001 001 000 Old_age
Offline - 2206
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age
Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always
- 3
202 TA_Increase_Count 0x000a 253 162 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 251 180 Pre-fail Always
- 0
204 Shock_Count_Write_Opern 0x000a 253 189 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 194 190 000 Old_age
Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 1159 inconsistent with error log pointer 5
ATA Error Count: 1159 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1159 occurred at disk power-on lifetime: 16996 hours (708 days + 4
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 6e 7a 2d ea Error: UNC 8 sectors at LBA = 0x0a2d7a6e =
170752622
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 6e 7a 2d ea 08 00:08:32.528 READ DMA
27 00 00 00 00 00 e0 08 00:08:32.528 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:08:32.512 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:08:32.496 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 08 00:08:32.496 READ NATIVE MAX ADDRESS EXT
Error 1158 occurred at disk power-on lifetime: 16996 hours (708 days + 4
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 6e 7a 2d ea Error: UNC 8 sectors at LBA = 0x0a2d7a6e =
170752622
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 6e 7a 2d ea 08 00:08:31.472 READ DMA
27 00 00 00 00 00 e0 08 00:08:31.456 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:08:31.440 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:08:31.424 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 08 00:08:31.424 READ NATIVE MAX ADDRESS EXT
Error 1157 occurred at disk power-on lifetime: 16996 hours (708 days + 4
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 6e 7a 2d ea Error: UNC 8 sectors at LBA = 0x0a2d7a6e =
170752622
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 6e 7a 2d ea 08 00:08:30.352 READ DMA
c8 00 08 86 5b 2d ea 08 00:08:30.352 READ DMA
c8 00 08 4e 3c 2d ea 08 00:08:30.336 READ DMA
c8 00 08 46 1d 2d ea 08 00:08:30.304 READ DMA
c8 00 08 26 dd 2c ea 08 00:08:30.304 READ DMA
Error 1156 occurred at disk power-on lifetime: 16778 hours (699 days + 2
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 a6 2b 11 e9 Error: UNC 8 sectors at LBA = 0x09112ba6 =
152120230
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a6 2b 11 e9 08 2d+23:52:03.776 READ DMA
27 00 00 00 00 00 e0 08 2d+23:52:03.760 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 2d+23:52:03.744 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 2d+23:52:03.728 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 08 2d+23:52:03.728 READ NATIVE MAX ADDRESS EXT
Error 1155 occurred at disk power-on lifetime: 16778 hours (699 days + 2
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 a6 2b 11 e9 Error: UNC 8 sectors at LBA = 0x09112ba6 =
152120230
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a6 2b 11 e9 08 2d+23:52:02.704 READ DMA
27 00 00 00 00 00 e0 08 2d+23:52:02.704 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 2d+23:52:02.688 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 2d+23:52:02.656 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 08 2d+23:52:02.656 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
wadesmart@wadesmart:~$